RC Motor Gear Puller and 4-in-1 RC Wheel Hex Hubs Wrenches Repair Set, Universal Motor Pinion Gear Puller Remover for Vehicle Model/Small Motor, Socket Spanner 4mm 5mm 5.5mm 7mm (1)

Parameter Information:Product Name: Motor Pinion Gear Professional Remover Surface Treatment: Chrome plating Type: Claw Puller Features:- Portable: Convenient to carry, lightweight and compact, and it is easy to install and disassemble.- Material: Omninmo motor pinion gear professional remover is made of metal material, efficient, wear resistant, stable and reliability, easy to use. It is a great tools for rc model car truck.- Save Your Money: Sometimes pinion gears wear out before electric motors get broken. Before getting a pricey new motor, try to replace the pinion gears first. That's when this pinion gear puller comes in handy. A money saver.- 5 Kinds Pins: This gear puller set includes five pins for pulling pinion gears of different sizes. Pins Size: 0.8mm(0.031in) (Cylindrical), 1.3mm(0.051in) (Semicircular), 1.5mm(0.059in) (Cylindrical), 1.6mm(0.062in) (Cylindrical), 2.2mm(0.086in) (Semicircular). Omninmo bearing puller can gear with a maximum outer diameter of 11mm(0.43in) and a tooth height of 12mm(0.47in) can be extracted.- Scope of Application: Omninmo gear puller set are suitable for remote control model, car inner rings and other dense components install and disassemble. Designed for removing bearings, inner rings and other dense components on your car. Pins Size: 0.9mm (Cylindrical), 1.75mm (Semicircular), 1.75mm (Cylindrical), 1.9mm (Cylindrical), 2.8mm (Semicircular) Usage of gear puller:1. Please select the needle according to the size of the motor shaft diameter. Do not use a motor with too small needle and too large shaft diameter for tooth extraction, otherwise the ejector pin will be broken. The glued gear must be heated to melt the glue before tooth extraction!!2. Select the tooth puller thimble you need, install the tooth puller rotating rod, and tighten the screw (Note: For a table thimble, the screw should not be too tight).3. Install the gear puller rotating rod into the gear puller bracket.4. Install the gear puller traveling plate.5. Clip the motor into the gear puller traveling plate and move it until the motor shaft aligns with the gear puller ejector pin.6. Rotate the gear puller lever uniformly in a clockwise direction to pull out the motor gear.7. Gear with a maximum outer diameter of 11 mm and a tooth height of 12 mm can be extracted. Place of Application:Use for pulling pinion gears off small and medium-sized motors such as rc modeling motors, door lock actuator motor, 3D printer extruder, stepper motors, electric track vehicle. Note:This gear puller is applicable to small motors with pinion gears of up to 11mm in diameter and at most 12mm in height.You are suggested to go slow when you try to pull the gears off.Some pinion gears are firmly glued to the motor. If so, please try to heat the gears up first. If the glue is not melting, you are not suggested to try to pull the pinion gears off.Size and Weight: Product Weight : 60 G / 2.12 Ounces Product Dimensions (L*W*H) : 5.0*3.5*1.5 CM / 1.97*1.38*0.59 Inches Package Weight : 82.0 G / 2.89 Ounces Package Dimensions (L*W*H) : 10.0*5.0*2.0 CM / 3.94*1.97*0.79 Inches Retail Packaging: Yes, Blister Packaging Package Include: 1 x Pinion Gear Puller 2 x Wrenches

• Save Your Money: Sometimes pinion gears wear out before electric motors get broken. Before getting a pricey new motor, try to replace the pinion gears first. That's when this pinion gear puller comes in handy! Alternatively, you can use a Phillips hex wrench to replace the wheel hub. A money-saver!
• 5 Kinds Pins: This gear puller set includes five pins for pulling pinion gears of different sizes. Pins Size: 0.8mm(0.031in) (Cylindrical), 1.3mm(0.051in) (Semicircular), 1.5mm(0.059in) (Cylindrical), 1.6mm(0.062in) (Cylindrical), 2.2mm(0.086in) (Semicircular). And Hexagonal Screwdriver Socket Specification 4mm(0.15in), 5mm(0.19in), 5.5mm(0.21in), 7mm(0.27in)
• Professional Motor Gear Remover and Hubs Remover:Omninmo bearing puller can gear with a maximum outer diameter of 11mm(0.43in) and a tooth height of 12mm(0.47in) can be extracted. And Hex Hubs Wrench suitable for 1/18,1/24/1/16 RC Car, some 1/10 RC Car is also suitable so make sure the specification matches your tire lug nuts before you buy
• Quality Material: Motor pinion gear puller and wrench is made of metal material, efficient, wear resistant, stable and reliability, easy to use
• Application: Omninmo pinion gear puller and wrench is designed for removing bearings, inner rings and other dense components on your car. Suitable for remote control model, car inner rings and other dense components install and disassemble